I went over some nautical terms associated with rigging and raising the mainsail. In this nautical beginner, we are going to discuss how to sail from day one, this being the first day. Hopefully, the wind is only at 5 or 6 knots, which makes it easy to maintain control of the sailboat, especially when this is your first time at the helm. Have a look at the following article taking us through the subject the first time to sailing chicago.
Should a new sailboat builder simply purchase rigging and sails? You know, it depends. Some plans, such as Chris Ostlinder's A18T trimaran, tend to be "high-tech."You can read about the A18T on the Duckworks website. These plans call for fittings and have stressed on things that are similar to what you see on Hobie Cats and things.
By the way, a tiller is the steering control mechanism on smaller nautical boats. However take note, the tiller steers in the opposite direction you will want to go. For instance, if you push the tiller towards the starboard [right side], the boat will steer to the left or the port side.
So unlike a car, the tiller works just the opposite! On the other hand, a ship wheel works the same as the steering wheel on an automobile. So depending on how your sailboat is equipped with a tiller or a ships wheel will determine how you will steer with it. I would recommend learning how to sail with the wind for a while before tacking or seafaring upwind.
Wash and Dry Sails at Season's End and Check Hanks, Slides, and Slugs: Hose down your sails with fresh water and dry them on a clothes line. Or, drape them over a few lawn chairs. This simple bath removes salt crystals and dirt, which can chafe sail-thread if left unattended. Jib or staysail hanks need the care to keep from freezing up with corrosion at the piston. The same goes for your mainsail slides (external) or slugs (internal). Wash these fittings with fresh water to keep them corrosion-free.
Inspect Your Stitching on Every Seam and lubricate your Mast Boom Slot: Thread holds your sails together. And after time, even triple-stitched panels, patches, and seams break down. Battens rub against pocket stitching, and sails flog and flap. Check the folded seam stitching along each sail edge. Next, move across each horizontal panel.
You can even tape pieces of tarp together at first. Then go back and sew them later if you want ... Or just leave them taped together. Another great thing about poly tarp is that you can try different things to create different types of sails. You can add shape to different sails by way of "darts." There is a great essay on the Duckworks website about cutting "darts" in sails to give them shape.
Next, you'll need to turn or come about. There are essentially two ways to accomplish this, by tacking or turning upwind is one way, or you can jibe or turn downwind which is faster than a tack turn. The reason being is that in a jibe turn you have the wind behind you pushing the sailboat through the turn, as opposed to a turning into the wind in a tack turn.
Should a new sailboat builder simply purchase rigging and sails? You know, it depends. Some plans, such as Chris Ostlinder's A18T trimaran, tend to be "high-tech."You can read about the A18T on the Duckworks website. These plans call for fittings and have stressed on things that are similar to what you see on Hobie Cats and things.
By the way, a tiller is the steering control mechanism on smaller nautical boats. However take note, the tiller steers in the opposite direction you will want to go. For instance, if you push the tiller towards the starboard [right side], the boat will steer to the left or the port side.
So unlike a car, the tiller works just the opposite! On the other hand, a ship wheel works the same as the steering wheel on an automobile. So depending on how your sailboat is equipped with a tiller or a ships wheel will determine how you will steer with it. I would recommend learning how to sail with the wind for a while before tacking or seafaring upwind.
Wash and Dry Sails at Season's End and Check Hanks, Slides, and Slugs: Hose down your sails with fresh water and dry them on a clothes line. Or, drape them over a few lawn chairs. This simple bath removes salt crystals and dirt, which can chafe sail-thread if left unattended. Jib or staysail hanks need the care to keep from freezing up with corrosion at the piston. The same goes for your mainsail slides (external) or slugs (internal). Wash these fittings with fresh water to keep them corrosion-free.
Inspect Your Stitching on Every Seam and lubricate your Mast Boom Slot: Thread holds your sails together. And after time, even triple-stitched panels, patches, and seams break down. Battens rub against pocket stitching, and sails flog and flap. Check the folded seam stitching along each sail edge. Next, move across each horizontal panel.
You can even tape pieces of tarp together at first. Then go back and sew them later if you want ... Or just leave them taped together. Another great thing about poly tarp is that you can try different things to create different types of sails. You can add shape to different sails by way of "darts." There is a great essay on the Duckworks website about cutting "darts" in sails to give them shape.
Next, you'll need to turn or come about. There are essentially two ways to accomplish this, by tacking or turning upwind is one way, or you can jibe or turn downwind which is faster than a tack turn. The reason being is that in a jibe turn you have the wind behind you pushing the sailboat through the turn, as opposed to a turning into the wind in a tack turn.
About the Author:
You can get a summary of the factors to consider when picking a sailing Chicago instructor and more information about an experienced instructor at http://www.saltydogchicago.com now.
Aucun commentaire:
Enregistrer un commentaire